Aml ACC-5910 M5900 In-Line Charger Manuale Utente Scaricare il pdf

User’s Guide

ACC-5910

M5900 In-Line Charger

Regulatory Information

All American Microsystems, Ltd. devices are designed to be compliant with

rules and regulations in locations they are sold and will be labeled as required.

Any changes or modifications to American Microsystems, Ltd. equipment, not

expressly approved by American Microsystems, Ltd., could void the user's

authority to operate the equipment.

Power Supply

Use only an American Microsystems, Ltd. approved Power Supply, output rated

5 VDC and minimum 2.4A. The Power Supply is certified to EN60950.

Disclaimer

American Microsystems, Ltd. reserves the right to make changes in specifica-

tions and other information contained in this document without prior notice,

and the reader should in all cases consult American Microsystems, Ltd. to

determine whether any such changes have been made. The information in this

publication does not represent a commitment on the part of American

Microsystems, Ltd.

American Microsystems, Ltd. shall not be liable for technical or editorial errors

or omissions contained herein; nor for incidental or consequential damages

resulting from the furnishing, performance, or use of this material.

This document contains proprietary information that is protected by

photocopied, reproduced, or translated into another language without the

prior written consent of American Microsystems, Ltd.

FCC Declaration of Conformity

Product Name: M5900 In-Line Charger

Model Number: ACC-5910

Radio Frequency Interference Requirements

This equipment complies with Part 15 of the FCC rules. Operation is subject to

the following two conditions: (1) This equipment may not cause harmful

interference, and (2) this equipment must accept any interference received,

including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class

A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference when the

equipment is operated in a residential environment. This equipment generates

uses and can radiate radio frequency energy, and if not installed and used in

accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not

occur in a particular installation. If you determine the equipment does cause

harmful interference to radio or television reception (this may be determined

by monitoring the interference while turning the equipment off and on), you

are encouraged to try to correct the interference by one of the following

measures:

· Reorient or relocate the receiving antenna.

· Increase the separation between the equipment and receiver.

· Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

· Consult the dealer or an experienced radio or TV technician for help.

Radio Frequency Interference Requirements - Canada

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du

Canada.

Marking and European Economic Area (EEA)

Products intended for sale within the European Union are marked

with the CE mark which indicates compliance to applicable

Directives and European Normes (EN), as follows. Amendments to

these Directives or EN’s are included.

· Electromagnetic Compatibility Directive 89/336/EEC

· Low Voltage Directive 73/23/EEC

Description of the RJ-45 10 Pin Connector (RS-232)

1 – 5 VDC (out to handheld tethered scanner)

2 – RxD (in to terminal)

3 – TxD (out from terminal)

4 – RTS (out from terminal)

5 – GND

6 – Battery Charge (in to terminal)

7 – CTS (in to terminal)

8 – UDC+ (USB data +)

9 – UDC – (USB data -)

10 – Battery Out (from terminal)

Note: the Battery Out is only active when the unit is set to IrDA w/RS232

Scanner or IrDA w/RS232 Comms

The ACC-5910 adapter has no internal or external settings that

can be changed.

Description of the DB-9 Connector (RS-232)

DB-9 Pin out (RS-232)

1 – DCD (Data Carrier Detect) 6 – DSR (Data Set Ready)

2 – RXD (Receive Data) 7 – RTS (Request To Send)

3 – TXD (Transmit Data) 8 – CTS (Clear To Send)

4 – DTR (Data Terminal Ready) 9 – NC (No Connection)

5 – GND (Signal Ground)

2190 Regal Parkway • Euless, TX 76040

800.648.4452 • Local: 817.571.9015

www.amltd.com • 800.648.4452

2190 Regal Parkway • Euless, TX 76040

800.648.4452 • Local: 817.571.9015

Note:

A standard 8-pin

Ethernet connector can

be used to connect the

M5900 to an RS-232

serial port printer. In

this case the 2 outside

pins (1 and 10) are not

connected. Use the

chart and example on

the right to determine

the pin-out.

1. RxD (in to terminal)

2. TxD (out from terminal)

3. RTS (out from terminal)

4. GND

5. No connection

6. CTS (in to terminal)

1 2

User’s Guide 1
Suggested Action 2

Sommario

Pagina 1 - User’s Guide

User’s GuideACC-5910M5900 In-Line ChargerRegulatory InformationAll American Microsystems, Ltd. devices are designed to be compliant with rul

Pagina 2 - Suggested Action

To connect power to the charger:1. Plug-in the Power Supply to a standard AC electrical outlet.2. Connect the Power Supply Plug to the barrel power

Commenti su questo manuale

Nessun commento

Aml ACC-5910 M5900 In-Line Charger Manuale Utente

Navigare online o scaricare Manuale Utente per Accessori per computer Aml ACC-5910 M5900 In-Line Charger. AML ACC-5910 M5900 In-Line Charger User Manual Manuale Utente

Sommario

Commenti su questo manuale